詳細解決方案請與我公司技術人員聯系：02885251762
01.0:YZ Communication with Engine PCA failed
01.1:YZ Error in the Engine PCA
01.2:YZ Failure communicating with an Ink Supply
02.1:YZ Problem with the Carriage PCA
03:YZ Problem with Power Supply Unit
03.0:10 Battery of Real Time Clock ran down
06:YZ Failure reading/writing NVM in Hard disk
07:10 Interconnect Board or Power cable has failed
07.01:11 DelSol3 ASIC not found or not responding
07.02:11 USB Cable not connected
07.03:10 USB Hub not found
07.03:11 USB Scanner connected to incorrect port
08:04 Touch Control Panel communication to the product functions at the initialization, but during
normal working the communication is lost.
08:08 A feature on the Touch Control Panel hangs or will not function (copy,scan etc)
08:11 No communication between the product and the Touch Control Panel
08:01:11 Touch Control Panel USB Cable fails
09:01 Media jam in Scanner
11:YZ Trailing Cable does not seem to be detected
21:YZ Failure moving Service Station
21.1:YZ Failure moving the Primer Motor of the Service Station
21.2:YZ Failure testing the length of the Service Station path
22.0:YZ Left Ink Supply Station error, module 0.
22.1:YZ Left Ink Supply Station error, module 1
24:YZ Ink Setup failure
26:01 Ink supply error found during IDS diagnostic test. In the Touch Control Panel message you will
see letters representing the names of the colors of the faulty supplies.
39.1:01 Roll 1 switch failed (standby or resume). Roll 1 has been unloaded.
39.2:01 Roll 2 switch failed (standby or resume). Roll 2 has been unloaded.
41:YZ Electrical fault or current limit in Media-Axis Motor
42:YZ Electrical problem (fault, current limit, overheating) in Scan-Axis Motor
45.1:YZ An error with the Rewinder 1 System (Upper Rewinder) has been detected.
45.2:YZ An error with the Rewinder 2 System (Lower Rewinder) has been detected
47:YZ Starwheels motor error
48:YZ PPS system failure
52:10 The product has detected a failure in the Drop Detector.
55:YZ Problem with the Line Sensor. The product has detected a failure to access the Line Sensor
EEPROM.
56:YZ Drive roller analog encoder homing (also known as “zero search”) failed.
59.1:09 Two electrical parts have been replaced at the same time.
59.2:00 An unsupported or reused part has been installed.
60.1:YZ, 60.2:YZ Initialization error
61:YZ The file format is incorrect or not supported for the current product configuration and the product
cannot process the job.
61:04.1 The PostScript fonts seem to be missing.
61:08.1 The file cannot be printed because it is password-protected.
63:01 Cannot retrieve IP addess
63:YZ Input/Output problem through the network interface of the Formatter
64:YZ Input/Output problem through the USB Port
64.1:YZ The External Hard Disk accessory does not seem to be connected
65:YZ Memory Driver Internal I/O error, I/O Socket Manager Internal I/O error
68:YZ Loss of engine counters tracking
71:03 Out of memory
71:04 Out of memory.
72.02:09 Generic firmware Error
72.02:YZ A service calibration should be performed.
74:YZ Error uploading firmware update file
75.21:YZ The spittoons (Left Spittoon, Service Station) have reached 80% capacity.
75.22:YZ The spittoons (Left Spittoon, Service Station) are full.
76:YZ Hard disk drive is full.
78:08 The job received cannot be printed without borders on this paper.
78.1:YZ Media settings area missing in paper settings file
79:YZ Generic firmware error
81:01 Paper axis error—the copier will restart and run a diagnostic test
86:01 Scan axis error—the copier will restart and run a diagnostic test
87:YZ Problem with the Carriage Encoder Sensor readings
87.01 Problem finding the Scan-axis encoder reading
93:YZ Unable to pressurize the Ink Delivery System
詳細解決方案，請與我公司技術人員聯系
聯系電話：13880436076
詳細解決方案，請與我公司技術人員聯系
聯系電話：13880436076
詳細解決方案，請與我公司技術人員聯系
聯系電話：13880436076
- 上一篇：筆架套的作用
- 下一篇：HP Designjet T120/520等固件升級的方法
